Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Jerith Kitchen Remodeling: The Los Angeles Owner’s Guide
If you have a Jerith kitchen and a part has failed, here’s the straight answer: we stock Jerith-compatible kitchen remodeling hardware and components at our Los Angeles shop, and a full kitchen remodel in Los Angeles typically runs $16,520 to $53,100 depending on cabinet count, countertop material, and how much plumbing or electrical has to move. Most owners discover a failing Jerith part the hard way: a drawer glides rough, a hinge sags, a pull-out shelf binds, or the finish on the cabinet frames starts wearing through where hands touch it daily. The good news is that a failed part rarely means a failed kitchen. We match the component, address what caused it to fail, and get your kitchen working like it should.
Mason Remodeling Co Los Angeles is an independent service provider. We’re not affiliated with Jerith, but we work with their cabinet lines and hardware regularly, and we know what holds up in LA’s dry heat and coastal humidity zones.
Which Jerith Models This Applies To
Jerith cabinetry shows up in Los Angeles homes under a few different series names, and the part you need depends on which one you have. Look inside a drawer box or on a cabinet door hinge plate for a small white or foil label. The series code and date of manufacture are usually printed there, and that’s the fastest way to get the right match.
The most common Jerith lines we see in LA are their framed cabinet series, which use standard 35mm European hinges and a mix of side-mount and under-mount drawer slides. The gotcha: some earlier Jerith models used a 42mm hinge cup bore instead of the standard 35mm, which means a generic replacement hinge will not seat correctly. If your door has the wider bore, you either need the Jerith-specific hinge or we drill and fill to adapt. We carry both paths on the truck.
On the OEM-versus-aftermarket question: for hinges and drawer slides, a quality aftermarket equivalent from a brand like Blum or Grass often outlasts the original and costs less. For anything cosmetic, like a matched door front or a finished end panel, the Jerith OEM part is the only way to keep the finish consistent. We’ll tell you which route makes sense before any work starts, and the written price covers whichever part we agree on.
Styles & brands we work with
Signs Your Jerith Kitchen Remodeling Is Failing
Here’s what we hear from Los Angeles homeowners when a Jerith kitchen part starts going, and what’s usually happening underneath each symptom:
- Drawer drops or scrapes when you open it. The slide’s ball bearings have worn flat spots or the nylon roller cracked. In LA’s dry inland air, the factory grease dries out faster than coastal homes, and metal-on-metal wear accelerates once that happens.
- Door won’t stay closed or sags at the corner. The hinge’s internal spring or clip has failed, or the door’s screw holes have stripped from years of opening. We see this most often on the double-door wall cabinets over the range, where heat cycles soften the hinge lubricant.
- Soft-close feature stopped working on a drawer or door. The damper cartridge inside the hinge or slide is blown. These are rated for a finite number of cycles, and a busy family kitchen in Los Angeles can hit that number in five to seven years.
- Pull-out shelf binds halfway or tilts. One side of the track has come out of alignment, usually because a mount screw backed out. If it’s been forced, the track itself may be bent and the whole assembly needs replacement rather than adjustment.
- Finish is worn through on cabinet frames near handles and knobs. This isn’t a single part failure, but it’s the signal that the cabinetry has reached the point where refacing or replacing worn components is more cost-effective than spot touch-ups.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Los Angeles, replacing a failed Jerith cabinet part as a standalone repair typically falls between $160 and $700 installed, depending on whether it’s a single hinge, a pair of drawer slides, or a full pull-out shelf assembly. If the failure is part of a larger kitchen remodel, the full project range of $16,520 to $53,100 reflects cabinet count, countertop choice, and whether we’re pulling new electrical or plumbing into the layout.
The written price you get from us includes the part, the labor to remove and replace it, the adjustment and alignment work so everything closes square, and haul-away of the old component. No surprise invoices at the end. The work is covered by our 365-Day Done Right Promise: if it’s not right within one year of completion, we make it right at no cost to you. Smaller related work, like cabinet installation alone, runs $4,720 to $15,340 in Los Angeles, and countertop installation runs $2,360 to $7,670.
DIY or Call Us?
Some checks you can safely do yourself: look for loose screws on hinge plates and slide mounts, clean caked grease off tracks with a degreaser, and check whether the cabinet door is simply out of alignment rather than broken. Those are adjustments, not repairs, and they cost you nothing but time.
Where DIY goes wrong is with the actual component swap. European hinges and soft-close slides have specific overlay and depth settings, and a mismatched part will bind or throw the door out of plane. If you have the older 42mm Jerith hinge bore, forcing a standard hinge will split the door and turn a $40 repair into a $400 door replacement. The part itself is not dangerous like a garage spring, but the cabinet door is under tension when a hinge is half-connected, and a slipping door can catch a finger. If you’re not certain about the part match, call (213) 632-5711 and we’ll identify it over the phone, usually from a photo.
FAQs
Factory hinges and slides on Jerith cabinetry in LA typically last 7 to 12 years before showing wear, less in inland heat zones like the Valley where dry air and higher temperatures break down lubricants faster. If your kitchen is past that age and multiple parts are failing, replacing components in batches is often less expensive than one-at-a-time service calls.
Hinges and drawer slides are sealed units and are not repairable; replacement is the only fix. The exception is a stripped screw hole in the cabinet frame, which we can fill and re-drill in about fifteen minutes. Call (213) 632-5711 with a photo of the part and we’ll tell you straight whether it’s a repair or a replacement.
A single hinge or one pair of drawer slides takes under an hour on site once we have the part matched. If we need to order a Jerith-specific cosmetic piece like a door front or finished panel, that’s usually a one to three week lead time in Los Angeles.
We stock common 35mm and 42mm Jerith-compatible hinges, standard side-mount and under-mount slides, and the soft-close damper cartridges in our Los Angeles trucks. Model-specific finished pieces are ordered from Jerith or a matched supplier. We also stock parts for KraftMaid, Cambria, and Silestone kitchens, so if your kitchen mixes brands, one call covers it. Call (213) 632-5711 for an exact quote, estimates are free.
Written by Isaac Pruett, Owner, Mason Remodeling Co at Mason Remodeling Co Los Angeles, serving Los Angeles and nearby areas.
